The Vernier Arduino Interface Shield plugs directly on top of the Arduino and adds two BTA (analog) and two BTD (digital) sockets. This shield was developed to be used with the SparkFun Arduino RedBoard but will work with the Arduino Uno and other Uno equivalents like the Leonardo. It also works with the Intel Galileo.
This adapter allows a Go!Temp or Go!Link* to connect to the USB port of a TI-Nspire handheld or TI-84 graphing calculator. The adapter has a USB standard-A receptacle which connects to the Go!Temp or Go!Link and a USB Mini-A USB plug that connects to the calculator. The adapter can also be used with the USB cable that comes with a Go!Motion.
The Motion Encoder Cart is a dynamics cart compatible with the Vernier Dynamics Cart and Track System. The Motion Encoder Cart replaces a motion detector when used for dynamics cart-on-track activities. An optical sensor beneath the dynamics cart senses the passage of the cart over a marked strip on the track. The position information is sent as an encoded IR signal to a receiver at the track’s end. By avoiding the possibility of stray sound reflections, this optical-only system provides excellent, repeatable, and noise-resistant motion data.
The adapter includes two connectors for Vernier analog sensors and one connector for Vernier digital sensors. A screw terminal and header pins provide access to myDAQ lines not used by the connectors. This includes the two analog output lines, three digital lines (including the digital lines with the frequency and pulse width modulation outputs), and a +5 volt power terminal.
The High Torque Generator is another option for your wind turbine generator. When compared to the standard Wind Turbine Generator, this High Torque Generator will produce lower voltage but higher current for a given rotor RPM. The High Torque Generator is great for load devices with higher current draw, such as the water pump. This generator has the same 2 mm driveshaft as the standard Wind Turbine Generator, so the Wind Turbine Hub is interchangeable with either motor. The generator also has 4-foot leads with shrink-wrap reinforced soldering.
The Oâ‚‚ gas sensor measures oxygen concentration in air, and is temperature compensated for use in different environments. It has a wide measurement range, allowing it to be used to study human and cellular respiration. The Oâ‚‚ gas sensor also includes a 250 ml bottle that can be used to study the rusting of iron, or as a respiration chamber for monitoring plants and insects.
The SparkFun RedBoard is an Arduino-compatible board that is perfect for use with the Vernier Arduino Interface Shield. It is a surface-mount board, which is pin-for-pin compatible with a R3 3 Arduino layout. The key difference between the RedBoard and most Arduino boards is that it uses a mini-B USB connector instead of a full-size, type-B USB connector.
The pH Buffer Capsules (3x10) kit is a convenient set of three vials containing capsules to make pH 4, pH 7, and pH 10 buffer standards for calibrating pH sensors. Each vial contains 10 capsules, each of which produces 100 mL of solution when mixed with DI water. Add three drops of the buffer preservative to 100 mL of your buffer solution to prolong the shelf life. Hydrion Color Key Buffer Preservative is a combination mold inhibitor and universal indicator for color coding the buffer solutions: orange for pH 4, green for pH 7, and blue for pH 10.
Vernier Chemistry Investigations for Use with AP* Chemistry lab book provides a comprehensive set of resources for the AP Chemistry teacher, including sample data, sample analysis and calculations, and helpful guides to assist in preparing reagents and chemical solutions. In addition, a carefully chosen set of step-by-step instructions for operating probes and software is included to help students make the best use of available lab time, while retaining the spirit of an inquiry environment.
The Vernier Circuit Board 2 is a basic electricity lab on a board. The turret terminals for every component make it easy to connect basic series and parallel circuits, examine the behavior of different components, and investigate RLC circuits. The Vernier Circuit Board 2 includes 10 bulbs, a resettable fuse, three powering options, 10 alligator clip leads, terminal clips to add components, and pre-installed components.
LabQuest Viewer is computer software that displays and controls the screen of a LabQuest using a computer. When used in conjunction with a projector, this software can be used to demonstrate the functions of LabQuest and to enhance group presentations. This software can also be used to monitor student use of LabQuest devices in the lab, view and control a LabQuest remotely, and easily capture LabQuest screen images for use in lab instructions or assessment questions.
Print…
List View
Easy View (new)
Facebook
Twitter
YouTube
Pinterest
Instagram