You searched for: standards

Supplier: Inorganic Ventures

200.7WW Cal Solution #3

Supplier: Inorganic Ventures

200.7WW LFS Solution #1

Supplier: Inorganic Ventures

100 ppb Mercury in HCl

Supplier: Inorganic Ventures

PerkinElmer ICP-OES UV Wavecal Solution

Supplier: Inorganic Ventures

USP<232>/ICH Q3D Class 2B Oral Elemental Impurities

Supplier: USP

USP Reference Standards are specified for use in conducting official USP–NF tests and assays. To confirm accuracy and reproducibility, USP Reference Standards are rigorously tested and evaluated by multiple independent laboratories including USP, commercial, regulatory, and academic labs. USP also provide publicly available, official documentary standards for pharmaceutical ingredients in the USP–NF that link directly with our primary reference standards.

Supplier: Hach

Stablcal® calibration standards kit, for 2100 series portable turbidimeters. USEPA accepted for calibration purposes. Stablcal® stabilized formazin turbidity standards are true formazin dilutions developed for use in any turbidimeter.

Supplier: Restek

Prepared from an equal-volume blend of 5W30, 10W30, 10W40, and 20W50 motor oils. After blending, a precisely weighed amount of the composite is added to a volumetric flask to produce the standard.
Motor Oil standards may exhibit lot-to-lot variation.

Supplier: SPEX CERTIPREP LLC

GAS-20 is a standard of Octane 87 gasoline for use in monitoring gasoline intrusion or pollution in the environment including water, soil and other environmental matrices.

Supplier: Hach

Stablcal® verification kit containing 0.10 NTU, 0.30 NTU, 0.50 NTU, 1.0 NTU standards (100 ml each), sililcone oil, oiling cloth and instructions is used for verification purpose only.

Supplier: Hach

For accuracy checks in iron determinations.

Supplier: TCI America

Class 3

Supplier: Hach

Standard solution for accuracy checks in copper determinations.

Supplier: TCI America

This reference material is used to confirm the peak separation. It is a mixture of the following components shown in Table below.

Supplier: WORLD PRECISION INSTRUMENTS LLC

Before attempting to use your sensor in an experimental solution, calibrate it under standard conditions to verify proper operation and performance.

Supplier: TCI America

Reference Material of Gasoline Components Certified by The Japan Petroleum Institute, /Methanol 1.5 volume% level/Ethanol 5.3 volume% level/MTBE 5.2 volume% level/ETBE 5.2 volume% level/Benzene 0.5 volume% level/Toluene 16.2 volume% level/Xylene 10.7 volume% level

Supplier: SPEX CERTIPREP LLC

CLP Standards for ICP & ICP-MS
Our Contract Laboratory Program (CLP) standards allow you to Calibrate with Confidence®. The standards are to be used in conjunction with the Statement of Work for Inorganic Analysis; Multi-Media/Multi-Concentration Document Number ILM 05.3/ISM 01.2.

The final ICP check, performed in our own laboratories, is your stamp of assurance. We calibrate our instruments with traceable reference materials and show you the actual found value of the solution you receive, not just an ideal, calculated number as so many other standards manufacturers do. The combination of elements, concentrations and matrices listed have been diagnosed by SPEX CertiPrep for convenience of use and stability.

US EPA SOW ILM 05.3/ISM 01.2 gives specific procedures for the methods of analysis, target elements, and concentrationlevels. Standards are specified not only by the elements present and their relative concentrations, but also the order and frequency of running standards, blanks and samples. Details of these specifications may be found in the US EPA SOW ILM 05.3/ISM 01.2 in the following sections:

• Exhibit C, Inorganic Target Analyte List (TAL)
• Exhibit D, Analytical Methods
• Exhibit E, QA/QC Requirements

CLP ISM 01.2 and ILM 05.2 & 05.3 Standards for ICP-MS
For verification of inter-element and background correction factors at the beginning and the end of each analysis run. In addition, a verification must be done after every 20th sample. Two solutions are required for the most common interference check: Solution A, the interferents alone (CL-INT-A2) and Solution AB, a combination of interferents (CL-INT-A2) and analytes (CL-INT-B3 or CL-INT-B4). Solution A is prepared by diluting CL-INT-A2 10-fold. Solution AB is prepared by diluting CL-INT-A2 10-fold and CL-INT-B3 or CL- INT-B4 100-fold; for example, 10 ml of CL-INT-A2 and 1 ml of CL-INT-B3 or CL-INT-B4 into a 100 ml volumetric flask, brought to volume with a matrix blank. Once prepared, the solutions should be analyzed consecutively, starting with Solution A.

Supplier: Restek

Hexachlorobenzene, Restek

Supplier: Restek

1,1,2-Trichlorotrifluoroethane (CFC-113), Restek

Supplier: Restek

5000ug/mL. Solvent: Isooctane. Packaged 1mL/ampule.

Supplier: Restek

Supplier: Restek

2000ug/mL. Solvent: Purge and Trap Grade Methanol. Packaged 1mL/ampule.

Supplier: Restek

200ug/mL in acetone, 5 mL/ampule.

Supplier: Restek

2000ug/mL. Solvent: Purge and Trap Grade Methanol. Packaged 1mL/ampule.

Supplier: Restek

2000ug/mL. Solvent: Purge and Trap Grade Methanol. Packaged 1mL/ampule.

Supplier: SPEX CERTIPREP LLC

CLP Standards for ICP & ICP-MS
Our Contract Laboratory Program (CLP) standards allow you to Calibrate with Confidence®. The standards are to be used in conjunction with the Statement of Work for Inorganic Analysis; Multi-Media/Multi-Concentration Document Number ILM 05.3/ISM 01.2.

The final ICP check, performed in our own laboratories, is your stamp of assurance. We calibrate our instruments with traceable reference materials and show you the actual found value of the solution you receive, not just an ideal, calculated number as so many other standards manufacturers do. The combination of elements, concentrations and matrices listed have been diagnosed by SPEX CertiPrep for convenience of use and stability.

US EPA SOW ILM 05.3/ISM 01.2 gives specific procedures for the methods of analysis, target elements, and concentrationlevels. Standards are specified not only by the elements present and their relative concentrations, but also the order and frequency of running standards, blanks and samples. Details of these specifications may be found in the US EPA SOW ILM 05.3/ISM 01.2 in the following sections:

• Exhibit C, Inorganic Target Analyte List (TAL)
• Exhibit D, Analytical Methods
• Exhibit E, QA/QC Requirements

CLP ISM 01.2 and ILM 05.2 & 05.3 Standards for ICP-MS
For verification of inter-element and background correction factors at the beginning and the end of each analysis run. In addition, a verification must be done after every 20th sample. Two solutions are required for the most common interference check: Solution A, the interferents alone (CL-INT-A2) and Solution AB, a combination of interferents (CL-INT-A2) and analytes (CL-INT-B3 or CL-INT-B4). Solution A is prepared by diluting CL-INT-A2 10-fold. Solution AB is prepared by diluting CL-INT-A2 10-fold and CL-INT-B3 or CL- INT-B4 100-fold; for example, 10 ml of CL-INT-A2 and 1 ml of CL-INT-B3 or CL-INT-B4 into a 100 ml volumetric flask, brought to volume with a matrix blank. Once prepared, the solutions should be analyzed consecutively, starting with Solution A.

Supplier: Cayman Chemical Company

A Certified Reference Material

Supplier: Cayman Chemical Company

A Certified Reference Material

Supplier: Cayman Chemical Company

A Certified Reference Material

Supplier: Cayman Chemical Company

A Certified Reference Material