You searched for: Microscopy and staining reagents

Supplier: Electron Microscopy Sciences

Mounting media for cover glass.  It comes in a convenient dispensing tube or bottle.   Solvent based which is soluble in xylene and has a 10 minute dry time.  Its viscosity is 33 cps at 25°.

Supplier: Electron Microscopy Sciences

EMS Shield Mount  is an aqueous non-permanent, low viscosity mounting medium for immunofluorescence. This unique formula prevents rapid photobleaching of FITC, Texas Red, AMCA, Cy2, Cy3, Cy5, Alexa fluoro 488, Alexa fluoro 594, Green fluorescent protein (GFP), tetramethyly rhodamine and Redox. The fluorescence is retained during storage at 4°C in the dark.

Supplier: Diagnostic Biosystems

fading agent for fluorescent staining.

Supplier: Electron Microscopy Sciences

A high temperature conductive paint.

Supplier: Mopec

Mopec’s Formaway formalin neutralizing powder safely and easily neutralizes spent formalin waste to a non-hazardous and non-toxic solution in only 20 minutes. Contents are emptied directly into 1 gallon of spent 10% Formalin or 4% Glutaldehyde, reducing risk exposure to lab personnel. This unique formula also eliminates drain-clogging polymers.

Supplier: Mopec

Amplify is a fixative spray usually applied after the application of Harmony dyes, although it can also be applied to tissue prior to marking with dyes.

Supplier: Electron Microscopy Sciences

Millonig’s phosphate buffered formalin as modified by Carson, Martin and Lynn, by using 4% formalin in 0.1M sodium phosphate monobasic with sodium hydroxide to pH 7.2

Supplier: Leica Biosystems

Sub-X® Clearing Agent is an economical xylene substitute that is an essentially odorless and non-greasy aliphatic hydrocarbon.

Supplier: Electron Microscopy Sciences

W.P.E. number included on each bottle.

Supplier: Electron Microscopy Sciences

A special adhesive with very high electrical conductivity and permanent plasticity.

Supplier: Electron Microscopy Sciences

An aromatic polyepoxide; a colorless resin of relatively low viscosity, with virtually no shrinkage.

Supplier: Electron Microscopy Sciences

Prepared from 3-aminopropyltriethoxysilane in acetone. Good for coating glass slides to adhere paraffin sections for further processing without sections falling off from the slide. READY TO USE.

Supplier: Electron Microscopy Sciences

Water based and isopropal based graphite adhesives.

Supplier: Electron Microscopy Sciences

EMS Immuno Mount™ with anti-fading agent 1, 4-Diazobicyclo-(2,2,2-octane (DABCO™) is an aqueous non-permanent low viscosity mounting medium for immunofluorescence.

Supplier: Electron Microscopy Sciences

An electrically Carbon Conductive Cement for specimen mounting in all SEM work.

Supplier: Electron Microscopy Sciences

Epo-Tek® H20S is a modified version of Epo-Tek®H20E

Supplier: Electron Microscopy Sciences

(A rapid mounting media for microscopy.) For long life preparations, without bubble formation at high ambient temperatures. It can be used for all dehydrated microscopic preparations. Cure time is 20 minutes at room temperature. It is colorless with an acid number less than 2.50 and a R.I. ND20 approx 1.49-1.5. (Contains xylene).

Supplier: Electron Microscopy Sciences

Hechman, C.A

Supplier: Electron Microscopy Sciences

HPMA is a water-soluble resin used for cytochemical applications

Supplier: Electron Microscopy Sciences

Silver adhesive in liquid and paste formats.

Supplier: Electron Microscopy Sciences

A water soluble embedding media which is based on Glycol Methacrylate (GMA) plastic embedding. It is intended for use in preparing samples for high resolution microscopes (HRLM). The catalyzed monomer acts as a dehydration and infiltration agent. Therefore, complete dehydration through 100% ethanol is not necessary although recommended for large or dense tissues. Conventional paraffin sections have a greater degree of shrinkage and produce inadequate morphology when compared to JB-4.JB-4 Kit Consists of 800 mL Solution A, 30 mL Solution B, and 12 g Catalyst.

Supplier: Electron Microscopy Sciences

With one swift application of the EMS Tissue Capture Pen, you are able to change your plain glass slide into a coated one.

Supplier: Electron Microscopy Sciences

This butyl acetate and acrylic resin mixture is the first mounting medium developed for coverslipping directly from d-limonene based clearants. Superior results are also with xylene. CitraMount® medium is recommended for manual coversliping only as it may cause damage to the valves of automated coverslippers.

Supplier: Electron Microscopy Sciences

A mixture of xylene - mixed isomers and non hazardous ingredients to offer a very good synthetic mountant. Once dried the refractive index is 1.58.

Supplier: Electron Microscopy Sciences

This electrically conductive silver epoxy is used for adhering samples, as well as many other purposes.

Supplier: AAT Bioquest

When exposed to excitation light, fluorescence intensity of dyes decreases due to their photooxidation or other photoreactions.

Supplier: AAT Bioquest

When exposed to excitation light, fluorescence intensity of dyes decreases due to their photooxidation or other photoreactions.

Supplier: Biotium

Wet-set antifade mounting medium for preserving fluorescence of our CF® dyes and other fluorochromes, in a dropper bottle for easy dispensing.

Supplier: Electron Microscopy Sciences

Fluoro Gel with antifading agent 1, 4-Diazobicyclo-(2,2,2-octane (DABCO™) is an aqueous mounting medium for preserving fluorescence of tissue and cell smears. This unique formula prevents rapid photobleaching of FITC, Texas Red, AMCA, Alexa fluoro 488, Alexa fluoro 594, Cy dyes, tetramethyly rhodamine, and Redox. The fluorescence is retained during prolonged storage at 4°C in the dark.

Supplier: Genetex

The PAP pen is a special marking pen that provides a thin film-like green-tinged hydrophobic barrier when a circle is drawn around a specimen on a slide